Fundamental Plumbing Insights for Bathtub Installation
Fundamental Plumbing Insights for Bathtub Installation
Blog Article
The author is making several great pointers about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround in general in the article down below.
Installing a tub isn't specifically rocket science, however it does call for strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old tub with a brand-new one is likewise a reasonably hard task. If the old bathtub is readily easily accessible, the job can relocate easily; if you need to open up a wall surface to get rid of the old bathtub as well as position the new tub, the task is much harder. In either case, the project is within a residence handyman's abilities, although you will certainly need a helper to vacate the old bathtub as well as embeded in the new one. Make sure you have actually certified yourself for the work as well as are comfortable trying it. As opposed to employing a specialist to take over a halfway-completed project, it is much better to consider using one before you start. Possibilities are you might need a specialist plumber to make tube connections.
This short article will certainly help you set up a new tub in your washroom if you have currently acquired a new tub as well as do not need to alter the plan of your previous supply of water pipes.
Your devices and product list need to make up the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your installation, after that the first thing you must do is detach the supply of water. After doing so, turn on the taps to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be fairly troublesome because of the restricted access that is typically the case.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the remaining water that will certainly originate from the pipes. As soon as the supply pipes have actually been eliminated, use the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from turning throughout this process. As soon as the taps have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old sealing substance.
Before carrying on to fit the brand-new taps, compare the pipe links on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to stop damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end gives a link to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly need lowering couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the tap in the placing opening in the bath/basin making sure that the washers are in place in between the faucet as well as the sink. Secure the faucet in position with the maker supplied backnut. When the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with normal faucet ports. The previous type should be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Installing the Tub
Making use of the two wood boards under its feet, position the bath tub in the required position. The wood boards are handy in evenly spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto four small factors.
The next goal is to guarantee that the bathtub is leveled all round. This can be attained by examining the spirit level and changing the feet on the bathtub till the spirit level reviews level.
To mount taps, fit all-time low of the outermost flexible faucet connector to the ideal supply pipe by making a compression sign up with; then do the very same for the other faucet.
Switch on the water as well as examine all joints and brand-new pipework for leakages as well as tighten them if necessary. Fill up the bath tub as well as also inspect the overflow electrical outlet and the normal outlet for leakages.
Finally, repair the bathroom paneling as described in the supplier's user's manual. Tiling and securing around the bathtub needs to wait till the tub has actually been utilized at the very least once as this will certainly settle it right into its final setting.
Preparing for the Installment
First of all, the sustaining frame provided with the bathroom ought to be fitted (if needed) according to the supplier's instructions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is important to see to it that if the faucet includes a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps device to avoid pressure on the tub.
Fit the adaptable tap adapters to the bottom of the two faucets using 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you utilize every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must currently be ready to be suited its last setting.
Tiling Around the Bath tub
In the area where the bathroom fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to split an inflexible seal, causing the water to permeate the wall surface in between the bathroom and also the tiling, leading to problems with moisture as well as possible leaks to the ceiling listed below.
You can choose from a variety of coloured sealers to blend in your fixtures and fittings. They are sold in tubes and cartridges, and are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with spins of soaked newspaper or soft rope. Remember to constantly fill up the tub with water before securing, to enable the movement experienced when the tub is in usage. The sealant can crack rather very early if you do not take into consideration this motion prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily offered on the market. It is a good idea to fit the tiles making use of water-resistant or water resistant sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a person who reads about A Step-by-Step Guide to Installing a Bathtub, I thought sharing that section was a smart idea. Enjoyed our review? Please share it. Help someone else discover it. I appreciate reading our article about Installing A Bathtub.
For instant fixes, dial! Report this page